USED EDGEBANDERS BRANDT & HOMAG
 | ||||
0803-03
HOMAG BAZ CNC EDGEBANDER MACHINING CENTER (Used)
Model: BAZ 41 Optimat; SN: 0-201-xx-xxxx; Year 1999.
480v; 60hz; 3ph.
Routing, Edgebanding & Boring Center with a 118-1/8" 48" working field.
Clamping Table:
•integrated in machine bed
integrated in machine bed•seven (7) clamping bars adjustable in X-direction
seven (7) clamping bars adjustable in X-direction•ten (10) vacuum cups, 140 x 115 mm (5-1/2" x 4-17/32"),
ten (10) vacuum cups, 140 x 115 mm (5-1/2" x 4-17/32"), 100 mm (3-15/16") high
two (2) vacuum cups, 45 x 115 mm (1-25/32" x 4-17/32"), 100 mm (3-15/16") high
•four (4)of the vacuum cups have integrated lifting devices
four (4)of the vacuum cups have integrated lifting devices•seven (7) submerging length stops
seven (7) submerging length stops•three (3) submerging side stops for alternate operation and processing in mirror image right hand
three (3) submerging side stops for alternate operation and processing in mirror image right hand•irregularly shaped panels have to be clamped using fixtures or mechanical clamps
irregularly shaped panels have to be clamped using fixtures or mechanical clamps•the machine zero point is to the front and left-hand side of the table
the machine zero point is to the front and left-hand side of the table•panels are fed manually from the front of the machine
panels are fed manually from the front of the machine HOMATIC "NC83" PLC Controller System with: Windows/NT 4.0 Operating system; 4-axis control: X, Y, Z & C; positioning speed of 2,362 IPM on X- & Y-axis.
Technical Specifications:
Work piece length: min. 250 mm (9-27/32") + 45 mm (1-25/32") overhang for flush trim, each side max. 3000 mm (118-1/8")
2 part processing length:1220 x 900 mm
1220 x 900 mmpanel width: min. 130 mm (5-1/8") + 45 mm (1-25/32") overhang for flush trim, each side max. 1220 mm (48")
Work piece thickness: max. 60 mm (2-3/8") Butt joint max.45 mm without edgebandingmax.200 mm (7-7/8")
max.200 mm (7-7/8") with special clamps or fixtures
with chamfer trimmingmin.12 mm (15/32")
min.12 mm (15/32") with radius trimming min. 2 x radius + 10 mm (13/32")
Edge height: max.65 mm (2-9/16")
max.65 mm (2-9/16")Edge thickness :- plastics 0.4 mm to 3 mm (0.016" to 0.118")
PVC min. = 1 mm (0.039")
Edge thickness- veneer: 0.4 mm to 2 mm (0.016" to 0.078")
Edge length:min.230 mm (9-1/16")
min.230 mm (9-1/16")Edge cross section - veneer:max.90 mm2 (.139 in2)
max.90 mm2 (.139 in2)Edge cross section - plastic:max.135 mm2 (.209 in2)
max.135 mm2 (.209 in2)Main spindle 12 kW (liquid cooled) with "HSK 63" quick change tool holder, spindle programmable from 1,500 - 18,000 RPM; features 0° - 360° C-axis swiveling range.
12-Position ATC carousel tool holder (max. dia. tooling 120 mm).
Boring head: (17) Vertical spindles with (11) spindles in X-axis, & (7) in the Y-axis driven by a 1.9 kW motor at 4,000 - 7,500 RPM variable speed;
Boring head: (4) Horizontal Spindles in all (4) directions.
drill chuck diameter:10 mm (13/32")
10 mm (13/32")drill length: 70 mm (2-3/4")
70 mm (2-3/4")drill diameter max.: 20 mm (25/32")
20 mm (25/32")effective length: 38 mm (1-1/2")
38 mm (1-1/2")rotations: 6000 rpm
6000 rpmGluing Unit: 360° Operation for straight edges with hot melt applicator and pressure rollers swiveling via C-axis, 30 mm min. inside radius and 300 mm min. part length for radius edgebanding, 0.4 - 3 mm PVC thickness and 0.4 - 2 mm veneer thickness.
One-Coil Magazine: for automatic coil material feeding and individual strip feeding device for banding in strip form, 65 mm max. edge height.
Workstations: Top & Bottom flush trim aggregate, 12k RPM;
T & B simultaneous trimming (approx. outside edge R = 0.5 mm., inside R = 50 mm via 0° - 360° C-axis).
Top & Bottom Profile Scrapping Aggregate (0° - 360° via C-axis) for scraping beveled or profile radius thick PVC banding.
Profile Scraping Unit:
•for automatic change in the main spindle
for automatic change in the main spindle •for post-processing of chamfers and radii at pre-trimmed PVC edges
for post-processing of chamfers and radii at pre-trimmed PVC edges•tracing from top and bottom
tracing from top and bottom•lateral tracing for compensation of panel and edge tolerances
lateral tracing for compensation of panel and edge tolerances•swiveling via C-axis from 0 to 360
swiveling via C-axis from 0 to 360 •without tools
without toolsProfile Knife for Scraping Unit:
•for radius 3 mm (1/8”)
for radius 3 mm (1/8”)Tool Collet Chuck Complete HSK 63B D=25 Left Hand
Homag Unit #7903
•tool chuck with hollow shaft cone HSK 63B
tool chuck with hollow shaft cone HSK 63B•integrated collet chuck mount for tool changer
integrated collet chuck mount for tool changer•collet chuck max. diameter 25 mm (31/32")
collet chuck max. diameter 25 mm (31/32")Tool Chuck-Collet Chuck Complete HSK 63B
D = 25 Right Hand
Homag Unit #7901
•tool chuck with hollow shaft cone HSK 63B
tool chuck with hollow shaft cone HSK 63B•integrated collet chuck mount for tool changer
integrated collet chuck mount for tool changer•collet chuck diameter 25 mm (31/32")
collet chuck diameter 25 mm (31/32")Grooving and Snipping:
•for automatic change in the main spindle
for automatic change in the main spindle•for grooving and cutting from top at any perpendicular angle to the work piece, snipping or edge overhang and panel separating as well as rectangular notchings
for grooving and cutting from top at any perpendicular angle to the work piece, snipping or edge overhang and panel separating as well as rectangular notchings•max. 9000 rpm
max. 9000 rpm•separating and snipping saws dia 180 x 30 x 3.2, t = 54
separating and snipping saws dia 180 x 30 x 3.2, t = 54•saw blade thickness max. 6 mm (1/4") for grooving
saw blade thickness max. 6 mm (1/4") for grooving •swiveling via C-axis from 0 to 360
swiveling via C-axis from 0 to 360Includes:
EtherNet Network connection with: TCP/IP,
CNC Programming system "WoodWop" for PC and 17" color monitor.
This machine is under power and can be demonstrated.
$142,500.00.
Replacement cost: $348,000.00 (approx)
FOB: Minnoseta.
This machine is offered “in good running condition as taken from service” and is subject to prior sale.
Specifications are approximate and to the best of our knowledge. Verification is available upon request.
USED MACHINERY
Browse By Application:
